Free Shipping For All US Orders Over $35 🎄 Holiday orders can take 3-4 business days to process

0

How to Apply Magnets to License Plate Covers

Your cover goes over your license plate and holds on with magnets. This page shows exactly where the two magnetic blocks go, and the easy way to get them in the right spot the first time.

What is in the box

  • Your plate cover. The whole back is magnetic.
  • Two super strong magnetic blocks. One side has adhesive under a peel-off liner.

Why the blocks are needed

License plates are aluminum, and magnets do not stick to aluminum. So the cover's magnetic back will not hold onto the plate itself. What it can hold onto is steel: the screws that hold your plate on, a steel plate frame, or a steel bumper.

The big magnetic back only touches the screw heads at a few small points, which is not always enough. The two magnetic blocks are much stronger and sit right on the screw heads, so the cover locks on.

Side view: plate mount, aluminum plate, steel screw, magnetic block, then your cover. Your plate mount (bumper or bracket) License plate: aluminum, magnets do not stick Steel screw head: this is what the magnet grabs Magnetic block Adhesive: sticks the block to the cover Your cover (magnetic back, design facing out)
Side view. The block grabs the steel screw, and the adhesive holds the block on your cover.

Where the magnetic blocks go

A regular license plate has four slots for screws. Your cover has no slots, so nothing interrupts your design. The magnetic blocks go on the back of the cover right where the top two slots would be, because that is where your plate screws are.

Back of a magnetic plate cover. Dashed outlines show where the slots would be on a normal plate. The two magnetic blocks go on the top two. Magnetic back (no slots) Magnetic block, over the top slot spot Dashed: where the slots would be 7 in. apart
Back of your cover. Dashed outlines show where the slots would be on a normal plate. Put the blocks on the top two.

Plate held on by the bottom screws only? Put the blocks on the bottom two spots instead. The blocks always go where your screws are.

The easy way: let your screws place the blocks

This works for any plate held on with steel screws. Do not measure. Put the blocks on your screws first, then press the cover onto them. The blocks end up exactly where your screws are.

  1. 1

    Clean the plate area

    Wipe the screw heads and the plate so they are clean and dry.

  2. 2

    Snap a block onto each top screw

    Hold a magnetic block against each top screw head. It snaps on. Keep the liner side facing out, toward you. Leave the liner on for now.

  3. Your license plate on the car, with a magnetic block snapped onto each top screw. Your plate mount YOUR STATE ABC 1234 liner liner Magnetic block snapped onto each top screw
    Step 2: a block on each top screw, liner facing out.
  4. 3

    Peel the liners

    With the blocks still on the screws, peel the liner off each one so the sticky side faces you.

  5. 4

    Line up the cover and press

    Hold the cover over your plate with the design facing out, line up the edges with your plate, and press it straight on. Press firmly over each block for about 30 seconds.

  6. 5

    Done

    The blocks are now stuck to the back of your cover, in exactly the right spot. Every time you put the cover on, the blocks find your screws. For the strongest hold, let the adhesive set for 24 hours before taking the cover off and on.

Prefer a guide? Print our plate template

Printable 6x12 license plate template: the plate outline and its four slots.
6x12 plate template: the outline and the four slots, at actual size.

Print this true-size template to see exactly where the slots sit. Lay it over the back of your cover, or hold it up to your plate, and use the slots to mark where the magnetic blocks go.

  • Legal paper (8.5 x 14): the whole plate on one sheet (page 1).
  • Letter paper (8.5 x 11): print pages 2 and 3 and tape them together at the center line.
  • Print at 100% / Actual size, not "Fit to page". Each page has a 1 inch square to check.

Download the template (PDF)

Have a steel license plate frame?

If your plate sits in a steel frame, or there is another magnetic surface around your plate, the blocks do not have to go on the screws. Put them anywhere along the top edge on the back of the cover, where they will touch the frame, and the cover sticks on that way too.

Back of a magnetic plate cover for a steel frame. The two magnetic blocks can go anywhere along the top edge, where they touch the frame. Magnetic back (no slots) Anywhere along the top edge Place the blocks where they will touch your steel frame
With a steel frame: the blocks go anywhere along the top edge, where they touch the frame.
  1. 1

    Check that your frame is steel

    Hold one of the blocks against the frame. If it grabs, the frame is magnetic. Plastic, aluminum and chrome-plated plastic frames will not hold; use the screw method above instead.

  2. 2

    Find where the frame meets the cover

    Hold the cover in place and note where the top bar of the frame will sit against the back of the cover.

  3. 3

    Stick the blocks along the top edge

    Peel the liners and press one block near each top corner of the back of the cover, inside that strip. Spread them apart for a steadier hold. Press firmly for about 30 seconds.

Tip: Try the cover on its own first. On a steel frame, the magnetic back alone may hold well, and the blocks make it even stronger.

Tips and fixes

The block will not stick to my screws

Your screws may be plastic or a stainless steel that is not magnetic. Test with any fridge magnet. Steel license plate screws cost a couple of dollars at any auto parts or hardware store; swap in two steel screws and the blocks will grab them.

My car has a steel license plate frame

Put the blocks anywhere along the top edge on the back of the cover, where they touch the frame. See Have a steel license plate frame? above. You can also try the cover on its own first, since the magnetic back may hold on a steel frame by itself.

The cover is a little off center

Within the first few minutes you can pull the cover off, slide the blocks off the cover, and repeat steps 2 to 4. After the adhesive sets, the position is fixed.

Does this work on a motorcycle plate (4x7)?

Yes, same steps. Motorcycle plates have screws in different places, which is why letting the screws place the blocks works better than measuring.

Can I drive with it on?

Magnetic covers are made for car shows, meets, photos and display. Take it off before driving on public roads; covering your registration plate while driving is against the law in most states.

Still stuck? Send us a photo of your plate and we will tell you where the blocks should go. Contact us or email support@whcustomco.com.